Keurig Still Says Descale After Descaling – Why Won’t My Keurig Descale Even After Following The Instructions?

keurig still says descale after descaling

​​​​​​​We all know that descaling our Keurig brewer is essential for maintaining quality performance and brewer longevity. However, what do we do when Keurig still says descale after descaling process has been completed? In this blog post, we’ll explore some potential reasons why your Keurig might be prompting you to descale again and offer some solutions to get your brewer back up and running like new. Enjoy!

What is descaling?

Descaling is the process of removing built-up calcium deposits, or limescale, from inside your Keurig brewer. Over time, these deposits can impede water flow and prevent your brewer from operating at peak performance.

These deposits can come from a variety of sources, including your water source, and can negatively impact the performance of your brewer. A good descaling cleaner will remove the deposits without harming your brewer’s internals. Descaling is important because it helps to keep your brewer working properly and at peak performance.

Why does my Keurig still say descale after descaling?

There are a few potential reasons why your Keurig might still say descale after you’ve completed the process.

First, it’s possible that there are still some deposits remaining in your brewer. This is especially common if you have hard water.

Second, it’s possible that the descaling solution didn’t reach all of the areas it needs to in order to properly clean your brewer.

Third, it’s possible that your descaling solution wasn’t strong enough to remove all of the deposits. If you’re using a vinegar-based solution, you might need to use a stronger commercial descaling product.

Fourth, it’s possible that your Keurig needs to be descaled more frequently than the recommended interval if you have hard water.

keurig still says descale after descaling
keurig still says descale after descaling

How to fix a Keurig still says descale after descaling?

If your Keurig keeps saying “Please descale,” there are a few things you can do to fix the problem.

Put the descaling solution in your brewer, followed by another cycle to make sure all of the deposits have been eliminated.

– Flush your brewer with fresh water to remove any residue from the descaling process.

– Run a brew cycle with no coffee grounds to clean out any residual cleaner and return your brewer to its default settings.

Place your cup inside another clean container. If any sticky particles remain, clean it and reuse them again.

Why is the descale light still on?

The descale light illuminates when some particles get trapped within the inner parts, usually jamming the needle. Clogged needles can prevent water from flowing and heating up effectively. When the descale light comes on as a signal that something is wrong and must be fixed, it indicates that there are clogs in the machine’s pipes. The descales need to be removed, and the descale light will go off.

Another potential reason your Keurig might not be brewing correctly is that the cup you’re using doesn’t fit properly, or if it’s been reused too many times and there are sticky particles clogging up the machine.

What to do to solve the descale light problem

There are a few things you can do to try to solve the descale light problem:

First, make sure that you’re using the right size cup for your Keurig. 

Second, clean your cup thoroughly before each use. 

Third, use a new filter if you’re using one. 

Fourth, use distilled water for the best possible cup of coffee. Remember, less is more when it comes to adding coffee grounds.

Fifth, try descaling your Keurig again with a commercial descaling solution. 

Sixth, change the water level that is suitable.

Last, if none of these solutions work, contact Keurig customer service for assistance.

What are the benefits of descaling my Keurig?

Descaling your Keurig has a number of benefits. First, it removes built-up calcium deposits that can impede water flow and prevent your brewer from operating at peak performance. Second, it helps to extend the life of your brewer by preventing scale build-up. Third, it helps to ensure that you’re getting the best possible flavor from your coffee by removing any impurities that might be present in your water. Finally, descaling is simply good preventive maintenance that will help to keep your Keurig running like new.

How often should I descale my Keurig?

The frequency with which you need to descale your Keurig depends on a few factors, including the hardness of your water and how often you use your brewer. In general, it’s a good idea to descale your Keurig at least once every three to six months. If you have hard water, you might need to descale more frequently. You’ll also need to descale more frequently if you use your brewer on a daily basis.

How to descale the Keurig?

If your Keurig needs to be descaled, there are a few things you can do to make the process easier.

Use a commercial solution

– Follow the package directions for the amount of solution to use.

– Add the solution to the water reservoir and fill it to the “MAX” line with water.

– Place a cup under the brew head and press the “brew” button.

– Let the machine run until it automatically powers off.

– Thoroughly rinse the brewer with fresh water to remove any residue.

– Clear out any residual cleaner by running a brew cycle without coffee grounds.

– Set your brewer back to its default settings.

Use vinegar

– Empty your water reservoir and discard any coffee grounds that are in the brew basket.

– Mix together one part white vinegar and two parts water in a bowl.

– Subsequently, pour the mixture into the water reservoir and put a cup under the brew head.

– Press the “brew” button and allow the machine to run until it shuts off automatically.

– Once the cycle is finished, discard the vinegar and water mixture.

– Rinse the brewer thoroughly with fresh water to remove any residue.

– Discard the water that is in the cup and run a brew cycle without coffee grounds to clear out any residual cleaner.

– Set your brewer back to its default settings.

Use lemon juice

Add 1/4 cup of lemon juice to the water reservoir and fill it to the “MAX” line with water. Turn on the coffee maker and wait for it to heat up. When the water has reached temperature, press the “brew” button and then follow the steps like using vinegar.

Using descalers

Descalers work by passing the water through a filter that contains an acidic solution. The acidic solution breaks down the calcium deposits that have built up on your brewer. As the water goes through the chambers, minerals accumulate on the chamber’s walls. When enough minerals accumulate, the water becomes too acidic and destroys the internal mechanisms of the equipment as well as jeopardizing its warranty.

So Keurig does not recommend using any type of descaler in their brewers. If you do choose to use a descaler, be sure to follow the package directions carefully.

keurig still says descale after descaling
keurig still says descale after descaling

Some tips to descale the Keurig

Clean your cup thoroughly before each use

It’s important to clean your cup thoroughly before each use to remove any coffee grounds that might be clinging to the sides. A quick rinse with warm water should do the trick. Be sure to dry your cup well before adding coffee grounds, as wet grounds can result in weaker coffee.

Use a new filter if you’re using one

If you’re using a paper filter, be sure to change it out for a fresh one before each brew. A clogged filter can impede water flow and prevent your brewer from brewing properly. Using a new one each time you descale your Keurig will help to remove any impurities that might be present in your water and result in a tastier cup of coffee.

Use distilled water if possible

If you can, use distilled water in your Keurig. Distilled water is free of impurities that can impact the flavor of your coffee. It’s also less likely to leave behind mineral deposits.

Only use Keurig-approved coffee pods

Be sure to only use Keurig-approved coffee pods in your brewer. Keurig-approved pods are designed to brew properly and will not damage your machine.

Do a trial run without coffee grounds

Before brewing a full pot of coffee, it’s always a good idea to do a trial run with just water to make sure your brewer is working properly. This will help to ensure that you get the best possible results.

Clean the Keurig Machine?

You’ll know it’s time to clean your Keurig when you notice that your coffee isn’t tasting as good as it used to. This is usually caused by a build-up of coffee oils and grounds on the brewing chamber walls.

To clean your Keurig, simply follow these steps:

– Unplug the brewer and remove the water reservoir.

– Remove any coffee grounds from the brew basket.

– Rinse the brew basket and reservoir with warm, soapy water.

– Use a soft cloth to wipe down the exterior of the brewer.

– Rinse the brew basket, reservoir, and exterior of the brewer with clean water.

– Dry all of the parts with a soft cloth.

– Reassemble the brewer and plug it in.

– To clean out the system, run a brew cycle without coffee grounds.

– Pour out the water that is in the cup.

Your Keurig should now be clean and ready to use!

Conclusion

We recommend following the descale instructions provided by Keurig still says descale after descaling. This will help to ensure that your brewer continues to function at its best. Have you had any issues with your brewer since descaling? Let us know in the comments.

FAQs

How do I clear the descale message on my Keurig?

To remove the descale warning from your Keurig, simply run a brew cycle without any coffee grounds. This will assist to eliminate any remaining cleaning agent left in your device.

How do I reset my Keurig plus after descaling?

To reset your Keurig plus after descaling, simply press and hold the “BREW” button for 3 seconds. This will deactivate the descaling mode and return your brewer to its default settings.

Why does my Keurig keep saying add water?

There are a few possible reasons why your Keurig might say “add water.” The most common reason is that the water reservoir is empty. Another possibility is that the float switch is stuck in the “off” position. The scale may collect in the brewer if there is too much scale build-up.

How do I force my Keurig to reboot?

If your Keurig is having issues and you need to force it to reboot, simply unplug the brewer from the power outlet and then plug it back in. This will reset the machine and hopefully fix any issues that you’re experiencing.

Is there a reset button on a Keurig K supreme?

Yes, there is a reset button on the Keurig K supreme. To find it, simply look under the water reservoir. The reset button is located next to the fill level indicator.

What does it mean when the Keurig add water light is red?

The “add water” light on your Keurig will turn red when the water reservoir is empty. Simply refill the reservoir and the light should turn green.

What does it mean when the Keurig add water light is orange?

The “add water” light on your Keurig will turn orange when the float switch is turned off. This can happen if there is too much scale build-up in the brewer. To fix this, simply descale your brewer.

Why Keurig owners are frustrated?

Keurig owners are frustrated because they have to descale their brewers more often than they’d like. Additionally, the process can be time-consuming and difficult to do properly. Finally, some Keurig owners have had issues with their brewers not working properly even after they’ve completed the descaling process.

Leave a Replay

Follow Us

Recent Posts

Stephanie Philpot

Stephanie Philpot

I'm Stephanie Philpot, Main editor and writer at identitycoffees. I have always been passionate about coffee, from the time I first tasted it. I love learning about all aspects of coffee: from the growing and harvesting to the brewing and roasting. I want to share my experience, receipts, knowledge, and more with everyone who is interested in learning more about this amazing drink. Coffee is more than just a morning ritual for me; it's a passion that I want to share with as many people as possible.

Sign up for our Newsletter

Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit

You May Also Enjoy These Articles